Hitachi GR2000 Series Manual de usuario Pagina 184
- Pagina / 328
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Hitachi Gigabit Router GR2000 Series Enhanced Version Operations - Device Management Overview
7-18 GR2K-GA-0015
Ver. 07-02
(g) Check out the ISDN POOL Status:
Using a show isdn-pool command, check out the state of ISDN POOL used by the
relevant communication peer. The remedy for ISDN POOL status is shown in the
table below.
7.4.2.2 Confirmation of Statistical Information
Confirm the statistical information below (frame send and receive failure) of the
relevant line or timeslot using the show interfaces command. If there is a frame send
or receive failure, conduct a line test and confirm that there is no malfunction in the
NIF board, cable or modem (*1).
Moreover, if a serial line is in use, check to see with the show interfaces command
whether an unsupported line speed has been set up. Note that NWVX-4, NWVX-8
and NWBMX2-4 differ from each other in the line speed they support. For line speed
supported by each NIF, see GR2000 Configuration Settings.
Table 7-16 Status Inspection/Action on ISDN Peer
No. ISDN Peer Status Cause Action
1 closed Connection to the peer is unavailable
because the peer is closed by the close
command.
Set the peer to active by using the free
command.
2 disabled Connection to the peer is unavailable
because the peer is disabled by
configuration information.
Enable the peer by altering the
configuration information.
3 restricted Connection to the peer is unavailable
because transmission to the peer is under
restriction.
Same as above.
4 Phone number
invalid
Connection to the peer is unavailable
because the registered phone number/
subaddress of the peer is different from
the actual one.
Correct the registered phone number/
subaddress of the peer.
5 ID invalid Connection to the peer is unavailable
because the registered authentication ID
of the peer is different from the actual one.
Correct the registered authentication ID of
the peer.
Table 7-17 Status Inspection/Action on Peer’s ISDN Pool
No.
Peer’s ISDN Pool
Status
Cause Action
1 channel use rate When this value shows no unused
channel, assignment of channel for
communication is unavailable.
Review the relationship between the
number of usable channels in an ISDN
pool and the number of peers.
2 Lost calls (originate) When this value keeps counting up,
assignment of channel for originating calls
is unavailable and originating calls are lost.
Same as above.
3 Lost calls (answer) When this value keeps counting up,
assignment of channel for answering calls
is unavailable and answering calls are lost.
Same as above.
- Hitachi Gigabit Router GR2000 1
- Series Enhanced Version 1
- (FCC) Compliance 2
- Trademarks 2
- Release 06-05 (January 2003) 3
- Change Record 3
- Abbreviations 5
- Acknowledgments 11
- [BSDI Internet Server] 13
- AT&T (DAVID M. GAY) 14
- INFO-ZIP GROUP 14
- INTERNET SOFTWARE CONSORTIUM 14
- SIGMASOFT, TH. LOCKERT 15
- SUN MICROSYSTEMS, INC 15
- UNIVERSITY OF TORONTO 16
- WILDBOAR 17
- MARTIN BIRGMEIER 17
- CHRISTOPHER G. DEMETRIOU 17
- DAVID HOVEMEYER 18
- FRANK VAN DER LINDEN 18
- THEO DE RAADT 19
- HENRY SPENCER 19
- [diff, grep] 20
- [tcpdump] 21
- [traceroute] 22
- [Apache HTTP server] 23
- [Xntp Program] 23
- [MD5 Program] 24
- [mrouted] 25
- [PIM sparse-mode pimd] 25
- [KATE IPv6 STACK] 26
- Safety Guide 29
- Specific Warning Instructions 30
- Specific Caution Instructions 31
- Other Instructions 32
- Table of Contents 33
- List of Figures 43
- List of Tables 49
- Chapter 1 51
- Before Operation Start 51
- GR2K-GA-0015 1-3 53
- 1-4 GR2K-GA-0015 54
- 1.2.1 Console 55
- 1.2.1.4 RS-232C 56
- 1.2.1.5 Modem 56
- 1.2.3 Backup MC 58
- Chapter 2 59
- Starting the router 59
- 2.2 Starting the router 61
- 2.3 Stopping the router 61
- 2.4 Logging in from a console 62
- Chapter 3 63
- Command operation 63
- 3.2.1 Login 65
- 3.2.2 CLI Actuation 65
- 3.2.3 CLI Termination 65
- 3.2.4 Prompt 66
- 3.2.5 Complement Function 67
- 3.2.6 Help Function 67
- 3.2.9 History Function 69
- 3.2.10 Pipe 70
- 3.2.11 Redirect Function 71
- 3.2.12 Paging 71
- 3.2.13 Warning Messages 71
- 3.2.15 Automatic Logout 72
- 3-16 GR2K-GA-0015 78
- Chapter 4 79
- 4.2 Setting login security 81
- 4.3 Setting the time 84
- 4.4.1 RM/RP board 85
- 4.4.2 NIF board 86
- 4.5.1 Overview 87
- 4.6 Consideration of security 88
- 4.7.1 Setting using command 89
- Terminal 90
- IP address of own router 91
- Must be “aux.” 91
- Double-click 92
- Click [OK] 94
- Double-click the 94
- Click [Next] 95
- [Make New Connection] icon 95
- Click [Finish] 97
- Click the new icon with 97
- Click [Properties] 97
- Click [Connect] 99
- 4-22 GR2K-GA-0015 100
- Ver. 07-02 100
- Chapter 5 101
- 5.1.1.1 Physical interface 102
- MAC address must have been 103
- 5.1.2.3 Frame Relay 104
- 5.1.2.1 Physical interface 104
- 5.1.2.2 PPP 104
- 5.1.2.4 ISDN PPP 105
- Both or either of the 116
- 5-20 GR2K-GA-0015 120
- 5.4.2.1 Interface information 121
- 5.4.2.2 Adjacent information 122
- This Router 123
- PIM Router 123
- (non-PIM) 123
- 5.4.3.1 Interface information 125
- 5.4.3.2 Adjacent information 126
- 5.4.4.1 Interface information 127
- 5.4.4.2 Group information 128
- 5-36 GR2K-GA-0015 136
- Figure 5-68 Log display 136
- 5.7.2.1 Interface information 140
- 5.7.2.2 Adjacent information 141
- 5.7.3.1 Interface information 143
- 5.7.3.2 Group information 144
- Confirm here 147
- Chapter 6 155
- Tasks During Operation 155
- 6.3 Confirming operation log 158
- 6.5 Confirming MC capacity 161
- 6.6.1 Adding the boards 162
- 6.7 Switching mode 164
- Chapter 7 167
- Troubleshooting 167
- 7.1.1 FAULT CODE is displayed 168
- 7.1.3 Mode cannot be switched 168
- 7.1.4 MC cannot be accessed 169
- 7.3.2 Dump file is created 175
- 7.3.3 Core file is created 176
- It must read “connected” 213
- MAC address must 213
- Confirm this content 217
- Section 5.2 219
- Both or one of these 220
- IP address has been set 222
- GR2K-GA-0015 7-57 223
- 7.7.2.1 PIM-SM network 227
- 7.7.2.2 PIM-SSM network 228
- [ROUTE-OS6] 231
- 7.8.3.1 Confirmation of State 238
- 7.10.1.1 PIM-SM network 246
- 7.10.1.2 PIM-SSM network 247
- 7.11.2.2 Check transfer state 250
- 7.11.7.2 Check label 253
- 7.11.7.4 Check LSP 253
- 7-90 GR2K-GA-0015 256
- COPS is Started 257
- COPS is in Operation 258
- SNMP manager 260
- Chapter 8 263
- Maintenance Procedure 263
- Changes the dialog mode 266
- Selects binary mode (Note 1) 266
- Transmits the dump file 266
- GR2K-GA-0015 8-5 267
- Status of the standby system 272
- Operation mode is “duplex.” 290
- Expand the RP memory 292
- Install the RP again 292
- Start operation of the RP 292
- Stop operation of the RP 292
- Remove the RP 292
- Type of line (must comply 297
- Status of line 297
- 8.7 Line Test 299
- 8.7.2 Testing on WAN Line 300
- Must be 0 305
- 8.7.3 Testing on ATM Line 306
- Must be “up” 307
- 8-46 GR2K-GA-0015 308
- Chapter 9 309
- Software updating 309
- 9.1 Outline 310
- 9.2 Operation after updating 311
- 9-4 GR2K-GA-0015 312
- Appendix 313
- < Alphabet > 314
- VBR queue 324
- Virtual links 324
© 2020, manymanuals.es. Todos los derechos reservados | 0.212 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales